Largest air volume in the industry. Drying is determined by temperature and air volume.
Processing volume
When drying on 30 resin trays, it is possible to process 180-210kg shiitake mushrooms and 3,000 pieces with persimmons.
Circulating indirect hot air drying
Clean hot air heated near the special furnace is sent to the drying room for drying. The standard heat source is an oil burner, and other gas / steam boilers / electric types are also available.
Safety
The main body uses bimetal to prevent overheating and shuts off the burner solenoid valve when it reaches 130℃ near the main body. Burner burns safely with flame detection CDS and protection relay control. The control version has double temperature control. Safety is ensured by double monitoring.
Outdoor exhaust
Improves drying efficiency by discharging moist air during drying to the outside.
Foreign matter countermeasures
Everything to dry food is shrimp shelf angle, door cover etc.
Outdoor exhaust
By keeping the moisture exhausted from the dryer room outdoors, the room where the dryer is installed is kept clean and dry.
3-stage airflow adjastment
By switching the amount of warm air, the quality can be finished in a short time. There is also a fuel saving effect.
Urethane insulation panel
The sandwich panel of double-sided color steel sheet sandwiched with urethane insulation material provides excellent heat insulation and durability. Polyurethane foam has a collection of small bubbles. Each of these small hard bubbles is an independent bubble, and the inside of urethane has a structure that prevents heat from conducting.
Oil burner
High-performance and safe burner with control relay, CDS (flame detection sensor), ignition transformer, electromagnetic pump, and blower motor. Pressure is applied by an electromagnetic pump, and vaporized fuel is ignited through a nozzle. At this time, appropriate air is sent forward by the blower motor. There are two types of burners: kerosene and A heavy oil specifications.
Resin tray
A container for placing dried products. The bottom is mesh. Size 600× 1200×30mm, made of resin (PP). In addition, it has a mesh structure that minimizes the contact area between resin and dry matter. The heat-resistant temperature is 70℃.
F
Digital standard
The thermistor sensor's built-in digital temperature control turns the burner on and off faithfully to the set temperature. The temperature and drying time are displayed separately on the digital display. In addition, a high-function control panel with added safety device function (double sensor) is installed. *The air volume switching function is only available on 60F and 30F.
PRO
Automatic damper
Intake and discharge (moist air) to the dryer body is automatically controlled. Control from fully open to fully closed automatically according to time. ※PRO Type
PRO
LCD
The graph can be displayed and the temperature, time, air volume, and damper can be freely programmed. ※PRO Type
Show functions
Option
Heat source change: gas burner
Gas burner with dozens of safety measures using LPG / city gas burner.
Option
Heat source change: steam boiler
When a steam boiler is already installed, additional piping is used for the plate fin heater of our dryer to use steam heat. Unlike an oil burner, it is a cleaner heat source because there is no need to smoke.
Option
Heat source change / power heater
A dryer that uses an electric heater as the heat source. A three-phase 200V power supply, unlike running oil, has a stable running cost. Unlike an oil burner, it is a cleaner heat source because there is no need to smoke.
Option
Cart
Specification modified to a cart that can move 30 drying trays at a time. You can work efficiently. The material can be selected from zinc plating, SUS304, and SUS430.
Option
Stainless steel body
It is possible to adopt a stainless steel specification both the full body or only for the drying room. SUS304 / SUS430 can be selected.
Option
Stainless steel tray
A tray for placing dried products. The bottom is mesh. There are two types of material: stainless steel SUS304 and SUS430. Size: 590 x 590 x 40(mm)
Option
Special air volume
The amount of warm air can be changed by changing the blower.
Show options
Type list
F
F type
Digital temperature control
Manual control exhaust damper
PRO
LCD
Program 30 pattern
Reservation timer
Graph display function
Temperature, time, air volume, damper can be set freely
interval timer function
Specification table
Model name
TB-30-F
TB-30-PRO
Dimensions （W×D×H）(mm)
1983×1488×2346
Tray
30 rasin trays
Tray size (mm)
600×1200 depth 30
Power supply
Single-phase 100V outlet capacity 15A
Power consumption 50/60Hz
670/835W
740/905W
Nozzle (G: Gallon)
1.35
Heat source
Kerosene, diesel or heavy oil *Gas, steam and electricity are available as options
Blower
Voltage ventilation fan 50cm 750W
Control pannel ＜Display＞
Digital
LCD
Control pannel ＜Temperature controller＞
Thermistor
Control pannel ＜Timer＞
End timer
Reservation timer・Interval timer・End timer
Control pannel ＜Airflow adjustment＞
Strong / Medium / Weak
Operation box ＜Auxiliary temperature control＞
－
10～100 steps temperature rising 30 pattern program
F
PRO
Option
Option
Option
Option
Option
Option
Option